Search : in
By :

Computer turns on, moniot says "no signal&quo

Last answer on Jun 29, 2009 9:15:04 pm BST kingofthegrill, on May 4, 2008 6:18:22 pm BST 
 Report this message to moderators

Hello,
I have been using this computer for around 4 years now. I recently had problems of it randomly turning off at any time, i could be working on a document, or the computer can be just sitting there, and it would turn off randomly.

I fixed that problem by backing up all my files on an external hard drive and simply reformatting. I was using a Wireless B PCI adapter for internet before reformat. Because of the reformat, it got uninstalled. So i took it out and installed it on another computer (which is liek two years older) because the modem is right beside this computer so i decided to run ethernet.

On the older computer, after installing the PCI card, the computer would turn off and go to a blue screen saying there is a hardware issue and stuff. So i would boot to last known good configuration and the card wouldnt be installed, so obviously there is the problem.

I took the PCI card out of that one and put it into the 4 year old computer to see if i would have the same problem, i didnt. Everything worked fine. I switched locations of the computers so one can use ethernet and one can use the wireless. After switching locations, the 4 year old computer did not work. It would turn on, fans are spinning, no beeps or anything, but nothing would display on the screen. I tried sticking in the xp disc so i can boot from that. I tried removing the hard drive. Nothing helped. No BIOS, no video. Then i decided to take out the wireless B PCI card, then the computer booted!!!!

No files lost or anything. The reason i wanted to fix this computer so badly and not jsut get a new one is cuz i just bought a geforce 8600 so i can hook it up to my projector with good quality. After installing the graphics card, i have the same problem. The computer starts, the fans are spinning, everything, but the computer wont load. No BIOS or anything.

I took out the Graphics Card, hoping it would boot like last time, but it didnt work this time.

Yesterday, i took out the battery for 30 seconds hoping to reset the BIOS and I replaced the RAM. Now I turn it on and the screen goes crazy. Lines going everywhere and stuff!!!

Yes one more thing, with this computer, when i turn it on, the fan goes hyperspeed for 5 seconds then calms down, its always done it, for the last 4 years! Now when i turn it on, both fans work, and the one that goes hyperspeed keeps going at hyperspeed.

O and yes i have tried multiple monitors. The one i am using right now works, but when plugged in to the other computer, it does that crazy screen thing.

The 4 yr old computer has integrated graphics, this is why i want to install a graphics card.

I have a gateway 420GR.
K i don't think i am forgetting anything. Please HELP!!!

Configuration: Windows XP
Firefox 2.0.0.14

Best answers for « Computer turns on, moniot says "no signal&quo » in :
Computer turns on but not booting OS Show Computer turns on but not booting OS Issue Solution Note Issue I've had my desktop computer for about one year now. It is an Acer Aspire E380. On Saturday afternoon, it was going a bit slow so I decided to restart it. However, once it...
"No Signal" message on Monitor Show“No Signal” message on Monitor When switching on your CPU, you can get the message “No Signal” displayed on your monitor, though the whole system is running. This issue might be due to several factors that you should check...
Computer makes a “Whistle” noise ShowComputer makes a “Whistle” noise A computer usually makes a weird “whistling” sound if it has detected a problem over the temperature of your processor. This can come from an overheating issue caused by the absence or defect in the...
It is now safe to turn off your computer! ShowIt is now safe to turn off your computer! On Windows systems the message "It is now safe to turn off your computer, since the motherboard and case permit, to ensure that the system starts automatically switched off. To do this...
Download Turn Off Monitor ShowTurn Off Monitor is a simple utility for turning off monitor by using either a hotkey or clicking an icon. To switch off your computer when it is not used allows to save energy. This small utility edited by RTSoftwares can run automatically when...

1

kingofthegrill, on May 6, 2008 3:39:05 am BST
  • +14

I removed the battery and took out the jumper, moved it from slot 1+2 to 2+3 and back to 1+2. Put the battery back in, and the it Booted. Problem solved, thanks!

Reply to kingofthegrill

2

loverboy, on Jun 6, 2008 7:06:45 pm BST
  • +33

How do i fix the moniot when i say no signal

Reply to loverboy

3

bren, on Jan 5, 2009 10:12:23 am GMT
  • +12

We got same problem. The monitor of my computer shows nothing at all but a black screen and i can see that my display monitor is not malfunctioning. I had laid my hands and done something to the BIOS of my computer before this happen. I did tried what I am knowledgeable to do after turning it on and shown nothing. I somehow removed the RAM and put it back. I also tried removing videocard and put it back after all but it never work after. What solves my prolem was when iI went to a computer technician and ask him to fix it. You must sent it to him. They know best what to do.

Reply to bren

4

kaity1144, on Jan 17, 2009 11:44:00 pm GMT
  • +46

My computer dose the same thing i would turn it on and it would say no signal check signal cable but the signal cable is fine i dont know what to do

Reply to kaity1144

5

 dingle berry, on Jun 29, 2009 9:15:04 pm BST
  • +11

Hello i having smae problem when moniot go black but show message of no signal when plug in back computer for sertane. what i do.

Reply to dingle berry