Bsnl broadband Type II modem with wifi [Solved]

First Check it the Wireless is turned on in the modem.
You must see the wireless light glow on.
If the WIFI is not turned ON, Check this link to Enable WIFI : How to Enable WIFI.

Before configuring wireless, connect your laptop through ethernet and connect it to http://192.168.1.1
If you were asked for username and password, give the username and password of your modem.
by default BSNL modems have username : admin and password : admin
After login, you will get the router configuration. Here, click on the Wireless Tab.
In Wireless section, give some name in the SSID (Serivce Set Identifiers), this SSID is also know as wireless network name.
Then click on the Security tab below the Wireless Tab. The name given for SSID will appear here.
Select WPA-PSK in Network Authentication and give the WPA Pre-Shared Key.
This Key is the Password for Secured wireless network,Which we need to give in the laptop to authenticate and connect to the secured network.
Give 0 (Zero) for WPA Group Rekey Interval.
After completing the above, Click SAVE/APPLY button. Your wirless configuration is saved now.
Now Reboot your modem, Go to Management tab, and click Save/Reboot
Wait till your modem restarts, Now your wirless network is ready for use.
Connecting to Wireless Network after configuring the WIFI.

Connect your laptop to the wireless network and you will be asked for the password. This is the one which you gave for WPA Pre-Shared Key.
Once you give the password correctly, you will be connected to the Secured Wireless network

log on to the router then open WAN then edit PPPoE protocol (first one).
port =0
VPI=0
VCI=35
SERVICE CATAGORY= UBR WITHOUT PCR
THEN CLIK NEXT
SELECT SECOND OPTION PPP over Ethernet (PPPoE) AND Encapsulation Mode SHOULD BE LLC/SNAP-BRIDGING.
CLICK NEXT
PPP USER NAME IS YOUR BSNL USER NAME AND PASSWORD
AND Enable Fullcone NAT & LAST OPTION Bridge PPPoE Frames Between WAN and Local Ports (Default Enabled) SHOULD BE CHECKED.

CHEERS

you need to go to properties and then advanced settings ......enable sharing and the select the type as wireless connection .....turn on WiFi of both the devices or if u dont have WiFi the connect both the devices by ethernet cable to the modem ...the other devicewill be automatically connected to the internet .....u dont need to dial nything fr this device

All u have to do is open Internet explorer and in the address bar u type in 192.168.1.1 an hit enter.This will take u to the modem admin page. Here use the default username and password which is " admin " in both cases to log into the modem console . on the left hand side you will see connection types, choose PPPoE and then on the right hand side of the screen you will get page where it will ask for the username and password again. Here you provide the user name and password provided to you by bsnl . The next few screens just leave them as it is and simply click next . On the last screen click on Save and Reboot button. This will reboot the modem and you will see the lights blinking on the modem . wait till all 4 lights are more or less stable . Then go to the Network connections tab on your PC or laptop and select right click on the icon Local Area connection. Select properties and in the next dialog box select Intenet protocol ( tcp /ip) and then click on properties. make sure Obtain Ip adress automatically and Obtain DNS automatically are selected . click on Ok and close . VIOLA !!! you have the Intenet at your fingertips

log on to the router then open WAN then edit PPPoE protocol (first one).
port =0
VPI=0
VCI=35
SERVICE CATAGORY= UBR WITHOUT PCR
THEN CLIK NEXT
SELECT SECOND OPTION PPP over Ethernet (PPPoE) AND Encapsulation Mode SHOULD BE LLC/SNAP-BRIDGING.
CLICK NEXT
PPP USER NAME IS YOUR BSNL USER NAME AND PASSWORD
AND Enable Fullcone NAT & LAST OPTION Bridge PPPoE Frames Between WAN and Local Ports (Default Enabled) SHOULD BE CHECKED.
...............................srisuribabu .......................