| 1 walex88, on Jun 16, 2008 7:11:57 pm BSTMake a cross cable for the connection and put the 2 pc under the same workgroup.And finally, add d below configuration 2 d LAN of d 2 system.
IP address eg.. 192.168.0.1 subnetmask 255.255.255.0
and2nd system 192.168.0.2 subnetmask 255.255.255.0
It will definitely work.giv me a feedback | 8 Jitendra Kumar, on Sep 12, 2008 11:45:52 am BSTHello friend,
I read your massage, I known what's you have problem.
About me: -
Name - jitendra Kumar Sharma
From - India (Bihar) muzaffarpur
I am student of BCA 5 SEM.
Ok
Your question is how to connect 2 system using LAN?
Ands is: -
1 step: - you have a cable his name is
TIA/EIA 568-B.2 CATEGORY 5e
And RJ45 connector
2step: - make a cross cable
1st point 2nd point of cable wires
1--------3
2--------6
3--------1
4--------4
5--------5
6--------2
7--------7
8--------8
Cable each wires setting.
3 steps: your computer have install Ethernet hardware
How to
Right click "my computer"
Move mouse "computer properties"
Click "hardware" tab menu
Click "Device Manager"
Device manager window is open
Check network adapter
"PCI Fast Ethernet NIC" is work or not?
If NIC device is work then do next work
Else Nick device have cross simple then double click NIC device.
And "Enable Device"
Device usage: use this device (enable)
End work
next
4 steps. Create a ip address to both system are not same (My network places)
Click: - "view network connections" in network tasks
Right click: - local area connection
Ex: Realtek RTL8139 family PCI
Click: properties
Click 'this connection uses the following item:'
Internet protocol (TCP/IP) click "properties"
Use the following IP address
Ex: -
1st PC 192.168.0.100
Subnet mask 255.255.255.0
2nd Pc 192.168.0.200
Subnet mask 255.255.255.0
Click "ok" "ok"
4 steps: dos command check connection
Ping ip address (other pc)
Ex: ping 192.168.0.100
They have checking connection
And massage report
5.click in network task Firwall setting change
Off (not recommended) both system.
6-check group are same in my computer properties "computer Name"
Ex: "workgroup"
7. Then plug in cable to computer pc1 pc2.
Then massage is display "network cable is plugging with 100mbps"
Then click "network placese" and click "view workgroup computer"
Note:
Windows Xp any new
1.568 cable is make in cross 1---3,2----6,3----1,6-----2
2.same work group name
3.if you have problem to generate to ip address so this is not important to computer because automatically assign ip address
4.if Ethernet is not work/ not install
You have installed it with "main board" cd
Insert cd in cd Rom click "my computer" "properties" "hardware" "device manager"
Right click NIC device and choose update device click next to fowling instruction.
5.firwall setting, anti viruse firewall setting.
6. Ms dos command ping is must be using.
Ping command using in dos
If massage is Request timed out.
So you have a cable problem.
Of work group problem.
So I hope you are understand my simple language. | 10 nageswara reddy, on Oct 6, 2008 6:06:01 am BSTHellofriend,
I read your ans iget every thing. but i didn't internet please give me ans my mail
THANK YOU | 12 Jitendra Kumar, on Oct 14, 2008 11:25:11 am BSTHello friend,
I read your massage, I known what's you have problem.
About me: -
Name - jitendra Kumar Sharma
From - India (Bihar) muzaffarpur
I am student of BCA 5 SEM.
Ok
Your question is how to connect 2 system using LAN?
Ands is: -
1 step: - you have a cable his name is
TIA/EIA 568-B.2 CATEGORY 5e
And RJ45 connector
2step: - make a cross cable
1st point 2nd point of cable wires
1--------3
2--------6
3--------1
4--------4
5--------5
6--------2
7--------7
8--------8
Cable each wires setting.
3 steps: your computer have install Ethernet hardware
How to
Right click "my computer"
Move mouse "computer properties"
Click "hardware" tab menu
Click "Device Manager"
Device manager window is open
Check network adapter
"PCI Fast Ethernet NIC" is work or not?
If NIC device is work then do next work
Else Nick device have cross simple then double click NIC device.
And "Enable Device"
Device usage: use this device (enable)
End work
next
4 steps. Create a ip address to both system are not same (My network places)
Click: - "view network connections" in network tasks
Right click: - local area connection
Ex: Realtek RTL8139 family PCI
Click: properties
Click 'this connection uses the following item:'
Internet protocol (TCP/IP) click "properties"
Use the following IP address
Ex: -
1st PC 192.168.0.100
Subnet mask 255.255.255.0
2nd Pc 192.168.0.200
Subnet mask 255.255.255.0
Click "ok" "ok"
4 steps: dos command check connection
Ping ip address (other pc)
Ex: ping 192.168.0.100
They have checking connection
And massage report
5.click in network task Firwall setting change
Off (not recommended) both system.
6-check group are same in my computer properties "computer Name"
Ex: "workgroup"
7. Then plug in cable to computer pc1 pc2.
Then massage is display "network cable is plugging with 100mbps"
Then click "network placese" and click "view workgroup computer"
Note:
Windows Xp any new
1.568 cable is make in cross 1---3,2----6,3----1,6-----2
2.same work group name
3.if you have problem to generate to ip address so this is not important to computer because automatically assign ip address
4.if Ethernet is not work/ not install
You have installed it with "main board" cd
Insert cd in cd Rom click "my computer" "properties" "hardware" "device manager"
Right click NIC device and choose update device click next to fowling instruction.
5.firwall setting, anti viruse firewall setting.
6. Ms dos command ping is must be using.
Ping command using in dos
If massage is Request timed out.
So you have a cable problem.
Of work group problem.
So I hope you are understand my simple language. | 13 ras, on Oct 14, 2008 8:00:06 pm BSTHi.hope will be fine. do u tell me .when I am going "vies work group computer" system is asking password but I didnt set any password.y it is asking |
| 15 rock, on Nov 1, 2008 3:21:05 pm GMTSir....
i means..
when we get an ip address such as.. 192.168.0.1
than we ping 192.168.0.1
that's give me a message " disination host unreachable" | 87 IMRAN, on Oct 21, 2009 2:03:45 pm BSTMY IP ADDRESS IS 192.168.1.1 AND 192.168.1.3 |
|
| 35 junaid, on Dec 29, 2008 6:01:44 pm GMTThanks very much mr jitendra |
| 44 Amrit, on Jan 27, 2009 4:39:38 am GMTI did not understand the 4th step. What do you mean by dos. Could you please elaborate the 4th step? i got all the steps done except for the 4th. Could you please explain me just the 4th step. |
| 46 balu, on Jan 29, 2009 5:29:29 am GMTThank you i will read your p2p solution. I will do it. its working i will shar my files easly thank you .
And one more dught for me i have two system both os or Xp i alredy connected p2p . Now i want to connect the
internet connection for both system . i have one way o/p modem plz replay me | 47 mido, on Jan 29, 2009 3:23:12 pm GMT1-connect the modem to your pc .
2-from the network setp wizard choose "This Computer Connects Directly to the internet .the other computers connext to the internet through this computer". with this you have you computer acts as Aresidental gate way.
3-on the other computer From the network setup wizard choose "This computer connects to internet through aresidental gateway or through another computer.
Don't forget to make amodem connection and connect to it. |
|
| 51 kilari, on Feb 21, 2009 4:53:04 am GMTYour msg was very helpfull. Is this procedure is applicable for 2 pc's running with different os.(EX:vista,XP) |
| 52 shashi, on Feb 23, 2009 2:55:57 pm GMTSir please
I know little bit about the computer
and i having 16 computer in my office. Sir please tell me that i want to connect all the computer and three printer in a single LAN by using cable.
There for sir please guide me the step by step procedure so that i can joint my all computer
Sir also i want to make a computer work as a server so please be kind to guide me the step by step process to set up the server and to connect the all computer and printers in LAN | 55 sahil, on Mar 3, 2009 8:19:28 am GMTDear i have a problem to make a workgroop .
i have a 22 computers , 5 lan card and five 8 poart switch and winxp professional windows .
than what can i make a networking the system . plz reply me as a document or flow chart . all divices are plagin the switch and computer through the coss & strate cable connection |
| 78 ss, on Aug 5, 2009 11:04:15 am BSTHello,
i understand your problem. you will use the switch to connect these computers and assign require ip addresses to each computer.if you have broadband or lease line then connect router in the network.share your server in the network so all other pcs can use internet connection..... |
|
| 53 noamn, on Feb 26, 2009 2:57:59 pm GMTSir i want 65000 ping comm for pc to pc checking. |
| 54 jack, on Feb 27, 2009 10:26:53 am GMTHiii
my name is jack
accactually i wants to add my new system in vlan . what is the step . if u know please tell me
this is brand new pc
i can aaply the ip add , |
| 72 john, on Jun 22, 2009 11:55:16 am BSTCan we connect two system directly through lan and share file...............
any difference b/w cross cable and lan.................. |
| 75 Sagar, on Jul 11, 2009 5:37:21 am BSTSir,
Your post makes me to able to connect two pc with each other, but pls let me know the colour of Cat5 in RJ45.
Thanking you
Sagar |
| 79 H.Rajkumar, on Aug 7, 2009 5:23:10 am BSTI just follow the instrustion given by JASTIS. And i have another problem "my system is connected in net through another computer it display the message LAN connected at 100mpbs but internet explore sould not open the web page. please clarify my problem. |
| 80 H.Rajkumar, on Aug 7, 2009 5:40:45 am BSTHai jitender thanks for your advice. please answer my another question. |
|
|
| 17 sanj, on Nov 6, 2008 4:05:47 pm GMTHello,
I have 4 system all with linux OS installed , I want to connect them In LAN can someone
suggest how do I go about it. I donot have much knowledge on Networking
Also kindly let me know What are the cable/connectors required to do so.
Thank you.
Regards,
-sanjay | 81 sree, on Aug 14, 2009 10:52:59 am BST |
|
| 19 papuu, on Nov 7, 2008 8:39:02 am GMT |
| 20 taj, on Nov 12, 2008 10:29:42 am GMTHi
about me
tajuddin
studying BE 2nd year ECE
from jangaon warangal (ap)
jitendra Kumar Sharma i fallowed u r instructions first day 2 systems are working using 1 internet connection next day it is not working in ping it displaying un reachable cable is connected both systems after re starting it showing 2 system is showing local area is connected 100 mbps after few minutes it showing un pluged in ping showing un reachable how to solve this proble please tll me taj | 68 Chilinomore, on May 6, 2009 6:56:04 pm BSTTo connect 2 PC's using LAN you need a crossover wire and change the "workgroup" and the computer's IP..
it could be a bit hard.. try to find a tutorial in the web.. |
|
| 24 Daljit, on Nov 29, 2008 5:05:10 pm GMTThanks a lot
u r a amazing. | 86 Carlington Kadete, on Oct 5, 2009 6:23:04 am BSTIts easy first make sure you have loaded the correct drivers for the network cards.Then from configure your computers putting them in the same workgroup.This can be done by clicking computer properties.computer name then change the workgroup .After that configure the ip adress eg put computer one to ip 192.168.0.1 subnet mask 255.255.0.0.After this share your files.You will notice that you are connected. |
|
| 29 umesh, on Dec 4, 2008 9:12:41 am GMT |
| 32 ankit, on Dec 18, 2008 7:34:01 am GMTThanks dude ur formule is working man |
| 38 Ashish, on Jan 10, 2009 7:41:42 am GMTHello
I am Ashish From jind Haryana
mai ek computer ko iind computers se boot karna chata hu iska apke pass koi formula hai kya
ho to plz mere ko batyega | 65 Krishan Kant Singh, on May 1, 2009 11:07:05 am BSTDear
Friend
If u want to boot from network your computer just go the run comand and type regedit and enter than you go to the file menu and go to the connect network registry and go to enter the object name to select here in the box you type your computer name or IP address Example----pc-102 or 192.168.0.9 as par. than you press enter button
NOTE- But this formula is runing only from networking and network system.
Thanks & Regards
Krishan Kant Singh |
|
| 56 siddesh, on Mar 20, 2009 12:49:46 pm GMTSir i have connected the two system in network by making cross connection.in pc1 am having two nic card because one for broad band another for lan net work but now i need to access the broad band in both the system .. what is the procedure.. to acess the broad band in both the system. |
| 64 jagath, on Apr 15, 2009 9:41:39 am BSTDear friend.
im from sri lanka.i got your information.thank's a lot for this information.i try to make this experyment first today.
thank you.
jagath priyantha |
| 67 harish chandra singh, on May 4, 2009 9:36:52 am BSTHi jitendra you ans is very easy and i am undarstnad problam very easy language
and i cantect and tack to you please send your mobile no
my mo no is 09425546607,9098761848. |
| 74 Biren, on Jun 26, 2009 5:17:12 am BSTThanks, Plz Send me ur contact No. |
| 82 mintu maurya, on Aug 14, 2009 3:51:25 pm BSTWhen pc start start internet automattically plz send me solutions plz |
| 83 ranaj, on Aug 16, 2009 6:46:07 am BSTHiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
no............................. |
| 88 Fahad (923009654997), on Oct 26, 2009 4:42:17 pm GMTHello,
Amazing, i love to read these easy step.
Thanks for this.
Fahad |
|
| 14 arvind, on Oct 29, 2008 2:35:26 am GMTHi friends,
please tell me how we connect two pc through crosss cable and if one pc have xp and another have vista |
| 61 kishan, on Apr 14, 2009 9:09:27 am BSTThak you so mach give to my answer but hwo to attach the cable in RJ45 cable |
| 70 jaan, on May 14, 2009 10:05:12 am BSTSir i don lan between 2 pcs given your instriction |
| 76 biddar, on Jul 15, 2009 7:39:50 am BSTI tried this but i unable to connect the internet please suggest some other method |
| 77 chandru, on Jul 15, 2009 10:08:26 am BSTMake a cross cable for the connection and put the 2 pc under the same workgroup.And finally, add d below configuration 2 d LAN of d 2 system.
IP address eg.. 192.168.0.1 subnetmask 255.255.255.0
and2nd system 192.168.0.2 subnetmask 255.255.255.0
The result is destination host notreachable |
| 84 please send procedure for connecting 2 systems through lan, on Aug 20, 2009 3:14:22 am BSTHello.
my name is dilip.studying btech.i want know how to connect 2 systems in lam.so please send the procedure for connect them,please send what are the requirements needed for that..
Please send reply to my mail id...
thankyou.. |
|
"intel pro/100 ve network connection" driver ethernet lan download